Electromotive Group Forum Index

Here to promote one of the most sophisticated EMS's known to man!
 
Home   FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups    CalendarCalendar   RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Welcome
Welcome to Electromotive TEC Group!.

wintec 341 error 57?

 
Post new topic   Reply to topic    Electromotive Group Forum Index -> TEC3/TEC3r
View previous topic :: View next topic  
Author Message
superspec
Newly Aquired


Joined: 04 Jun 2008
Posts: 18
PostPosted: Thu Oct 23, 2008 9:26 pm    Post subject: wintec 341 error 57? Reply with quote
darkgsx made a new map for me a whileback, and i finally got to try it out the other day. everything worked fine until the next time i tried to start the car. now its throwing error57 which i feel sure is a problem with the map being saved to the tec3. unfortunatly my laptop is still on ME and my flashdrive doesnt work on anything older than XP so my map is saved to a floppy. my old map that is on the same floppy is working fine, so i cant figure out why the new map wont work now? any ideas guys?
Back to top
TimZ
founding member


Joined: 25 Feb 2008
Posts: 120
Location: Dearborn, Michigan
PostPosted: Thu Oct 23, 2008 9:41 pm    Post subject: Re: wintec 341 error 57? Reply with quote
superspec wrote:
darkgsx made a new map for me a whileback, and i finally got to try it out the other day. everything worked fine until the next time i tried to start the car. now its throwing error57 which i feel sure is a problem with the map being saved to the tec3. unfortunatly my laptop is still on ME and my flashdrive doesnt work on anything older than XP so my map is saved to a floppy. my old map that is on the same floppy is working fine, so i cant figure out why the new map wont work now? any ideas guys?


Error code 57 is defined as a "Spare Output Failure", specifically the spare output is either in an over current situation or is shorted to 5V.
_________________


Information is not knowledge
Knowledge is not wisdom
Wisdom is not truth
-FZ, Joe's Garage
Back to top
superspec
Newly Aquired


Joined: 04 Jun 2008
Posts: 18
PostPosted: Thu Oct 23, 2008 9:43 pm    Post subject: Reply with quote
SOF would refer to what exactly? i dont have my manual handy at the moment.
Back to top
TimZ
founding member


Joined: 25 Feb 2008
Posts: 120
Location: Dearborn, Michigan
PostPosted: Fri Oct 24, 2008 1:23 am    Post subject: Reply with quote
superspec wrote:
SOF would refer to what exactly? i dont have my manual handy at the moment.


Apparently it's an output that can be used to light an LED to indicate that the internal datalogging is running.

Quote:
F.4.b. The Spare Output Function and Harness Layout
The spare output is configured as a pull-to-ground output for the activation of a Datalog
Status Light. If the spare output is wired to a light bulb, the light will flash when the on-board
datalogging function has been turned on. When the datalogging function is turned off, the light
will cease to flash. Wire the spare output light as you would a shift light (see Figure F.4 2).
Section X provides a more in-depth look at the Datalog Status Light.


Spare Output Wiring Harness Layout
Spare Output Terminal G21 White w/ Orange Stripe
(note: early units may use White w/ Black Stripe)

_________________


Information is not knowledge
Knowledge is not wisdom
Wisdom is not truth
-FZ, Joe's Garage
Back to top
DarkGSX
Newly Aquired


Joined: 03 Mar 2008
Posts: 7
PostPosted: Sat Oct 25, 2008 7:29 pm    Post subject: Reply with quote
Ask Travis to be sure but I don't think he would have wired that SOF up on your car unless you requested it. In that case you need to check wiring coming out of the Tec plug and make sure that wire isn't making contact with anything else.
Back to top
superspec
Newly Aquired


Joined: 04 Jun 2008
Posts: 18
PostPosted: Sat Oct 25, 2008 8:40 pm    Post subject: Reply with quote
its weird D, it took your map one time but i didnt save it to the tec, the next time i got in the car i had to load the disc again but it woulnt take it that time. the car ran much better with your map though.
Back to top
DarkGSX
Newly Aquired


Joined: 03 Mar 2008
Posts: 7
PostPosted: Sat Oct 25, 2008 11:24 pm    Post subject: Reply with quote
Did you ever program the tec with that bin file?
Back to top
superspec
Newly Aquired


Joined: 04 Jun 2008
Posts: 18
PostPosted: Sun Oct 26, 2008 1:43 am    Post subject: Reply with quote
DarkGSX wrote:
Did you ever program the tec with that bin file?


yea i did get to drive it with your map and it ran much smoother. i guess either i didnt save it to the tec or the tec just decided not to take it. ill have to get somebody more computer literate than myself to help me with it i guess. remember the walk through you had to give me on the thumbdrive?
Back to top
DarkGSX
Newly Aquired


Joined: 03 Mar 2008
Posts: 7
PostPosted: Sat Nov 01, 2008 7:58 pm    Post subject: Reply with quote
Can you get your computer buddy to help you with it?
Back to top
superspec
Newly Aquired


Joined: 04 Jun 2008
Posts: 18
PostPosted: Sat Nov 01, 2008 9:15 pm    Post subject: Reply with quote
yea ill prob have to. only problem with that is finding time, between work, school, and wife/baby i dont have spare time for cars really Sad
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Electromotive Group Forum Index -> TEC3/TEC3r All times are GMT
Page 1 of 1   

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum